WD Red Pro Review: 4 TB Drives for NAS Systems Benchmarkedby Ganesh T S on August 8, 2014 9:00 AM EST
Introduction and Testbed Setup
A couple of weeks back, Western Digital updated their NAS-specific drive lineup with 5 and 6 TB Red drives. In addition, 7200 RPM Red Pro models with 2 - 4 TB capacities were also introduced. We have already looked at the performance of the WD Red, and it now time for us to take the WD Red Pro for a spin. In our 4 TB NAS drive roundup from last year, we also indicated that efforts would be taken to add more drives to the mix along with an updated benchmarking scheme involving RAID-5 volumes. The Red Pro gives us an opportunity to present results from the evaluation of various drives that have arrived in our labs since then.
The SMB / SOHO / consumer NAS market has been experiencing rapid growth over the last few years. With declining PC sales and increase in affordability of SSDs, hard drive vendors have scrambled to make up for the deficit and increase revenue by targeting the NAS market. The good news is that the growth is expected to accelerate in the near future (thanks to increasing amounts of user-generated data through the usage of mobile devices). In addition, security threats such as SynoLocker have also underscored the necessity of frequent backups.
Back in July 2012, Western Digital began the trend of hard drive manufacturers bringing out dedicated units for the burgeoning SOHO / consumer NAS market with the 3.5" Red hard drive lineup. The firmware was tuned for 24x7 operation in SOHO and consumer NAS units. 1 TB, 2 TB and 3 TB versions were made available at launch. Later, Seagate also jumped into the fray with a hard drive series carrying similar firmware features. Over the last two years, the vendors have been optimizing the firmware features as well as increasing the capacities. On the enterprise side, hard drive vendors have been supplying different models for different applications, but all of them are quite suitable for 24x7 NAS usage. While mission-critical applications tend to use SAS drives, it is the nearline SATA versions that are more suitable for home / SMB users. These enterprise drives provide better reliability / longer warranties compared to the NAS-specific WD Red and the Seagate NAS HDD lineups.
The correct choice of hard drives for a NAS system is influenced by a number of factors. These include expected workloads, performance requirements and power consumption restrictions, amongst others. In this review, we will discuss some of these aspects while evaluating ten different hard drives targeting the NAS market. One of the most glaring omissions in our list is HGST's Deskstar NAS. Due to HGST's strange sampling scheme, we are still trying to obtain enough drives for our NAS-specific benchmkaring, but they did send us their 4 TB SAS drive for participation in this roundup. Other than the HGST SAS drive, the other nine drives all carry a SATA interface.
- WD Red Pro (WD4001FFSX-68JNUN0)
- Seagate Enterprise Capacity 3.5" HDD v4 (ST4000NM0024-1HT178)
- WD Red (WD40EFRX-68WT0N0)
- Seagate NAS HDD (ST4000VN000-1H4168)
- WD Se (WD4000F9YZ-09N20L0)
- Seagate Terascale (ST4000NC000-1FR168)
- WD Re (WD4000FYYZ-01UL1B0)
- Seagate Constellation ES.3 (ST4000NM0033-9ZM170)
- Toshiba MG03ACA400
- HGST Ultrastar 7K4000 SAS (HUS724040ALS640)
The above drives do not target the same specific market. For example, the WD Red and Seagate NAS HDD are for 1- 8 bay NAS systems in the tower form factor. The WD Red Pro is meant for rackmount units up to 16 bays, but is not intended to be a replacement for drives such as the WD Re, Seagate Constellation ES.3, Seagate Enterprise Capacity v4 and the Toshiba MG03ACA400 which target enterprise applications requiring durability under heavy workloads. The WD Se and the Seagate Terascale target the capacity-sensitive cold storage / data center market.
Testbed Setup and Testing Methodology
Unlike our previous evaluation of 4 TB drives, we managed to obtain enough samples of the new drives to test them in a proper NAS environment. As usual, we will start off with a feature set comparison of the various drives, followed by a look at the raw performance when connected directly to a SATA 6 Gbps port. In the same PC, we also evaluate the performance of the drive using some aspects of our direct attached storage (DAS) testing methodology. For evaluation in a NAS environment, we configured three drives of each model in a RAID-5 volume and processed selected benchmarks from our standard NAS review methodology. Since our NAS drive testbed supports both SATA and SAS drives, but our DAS testbed doesn't, the HGST SAS drive was not subject to any of the DAS benchmarks. We plan to carry more detailed coverage of the HGST SAS unit in a future SAS-specific roundup.
We used two testbeds in our evaluation, one for benchmarking the raw drive and DAS performance and the other for evaluating performance when placed in a NAS unit.
|AnandTech DAS Testbed Configuration|
|Motherboard||Asus Z97-PRO Wi-Fi ac ATX|
|CPU||Intel Core i7-4790|
Corsair Vengeance Pro CMY32GX3M4A2133C11
32 GB (4x 8GB)
DDR3-2133 @ 11-11-11-27
|OS Drive||Seagate 600 Pro 400 GB|
|Optical Drive||Asus BW-16D1HT 16x Blu-ray Write (w/ M-Disc Support)|
|Add-on Card||Asus Thunderbolt EX II|
|Chassis||Corsair Air 540|
|PSU||Corsair AX760i 760 W|
|OS||Windows 8.1 Pro|
|Thanks to Asus and Corsair for the build components|
In the above testbed, the hot swap bays of the Corsair Air 540 have to be singled out for special mention.
They were quite helpful in getting the drives processed in a fast and efficient manner for benchmarking. For NAS evaluation, we used the QNAP TS-EC1279U-SAS-RP. This is very similar to the unit we reviewed last year, except that we have a slightly faster CPU, more RAM and support for both SATA and SAS drives.
The NAS setup itself was subjected to benchmarking using our standard NAS testbed.
|AnandTech NAS Testbed Configuration|
|Motherboard||Asus Z9PE-D8 WS Dual LGA2011 SSI-EEB|
|CPU||2 x Intel Xeon E5-2630L|
|Coolers||2 x Dynatron R17|
|Memory||G.Skill RipjawsZ F3-12800CL10Q2-64GBZL (8x8GB) CAS 10-10-10-30|
|OS Drive||OCZ Technology Vertex 4 128GB|
|Secondary Drive||OCZ Technology Vertex 4 128GB|
|Tertiary Drive||OCZ Z-Drive R4 CM88 (1.6TB PCIe SSD)|
|Other Drives||12 x OCZ Technology Vertex 4 64GB (Offline in the Host OS)|
|Network Cards||6 x Intel ESA I-340 Quad-GbE Port Network Adapter|
|Chassis||SilverStoneTek Raven RV03|
|PSU||SilverStoneTek Strider Plus Gold Evolution 850W|
|OS||Windows Server 2008 R2|
|Network Switch||Netgear ProSafe GSM7352S-200|
We thank the following companies for helping us out with our NAS testbed:
- Thanks to Intel for the Xeon E5-2630L CPUs and the ESA I-340 quad port network adapters
- Thanks to Asus for the Z9PE-D8 WS dual LGA 2011 workstation motherboard
- Thanks to Dynatron for the R17 coolers
- Thanks to G.Skill for the RipjawsZ 64GB DDR3 DRAM kit
- Thanks to OCZ Technology for the two 128GB Vertex 4 SSDs, twelve 64GB Vertex 4 SSDs and the OCZ Z-Drive R4 CM88
- Thanks to SilverStone for the Raven RV03 chassis and the 850W Strider Gold Evolution PSU
- Thanks to Netgear for the ProSafe GSM7352S-200 L3 48-port Gigabit Switch with 10 GbE capabilities.
Post Your CommentPlease log in or sign up to comment.
View All Comments
willis936 - Friday, August 8, 2014 - linkThank you for the overview of ATA protocol features on page 3. Resources like that are hard to find without spending hours digging through a spec.
Anonymous Blowhard - Friday, August 8, 2014 - link"Enterprise" or not, running RAID5 on 4TB drives with a 10^14 URE is asking for trouble.
Guspaz - Friday, August 8, 2014 - linkOnly when rebuilding. The chances of getting a read error on two disks at the same time on the same piece of data is extremely remote. Of course, when rebuilding, you only need the error on one disk... which is why I'm running raidz2 :)
rufuselder - Thursday, October 9, 2014 - linkI'd say WD AV-GP 2 TB AV is the best choice (supported by for example http://www.consumertop.com/best-computer-storage-g... ). I'm not a big fan of raidz2, sorry.
NonSequitor - Friday, August 8, 2014 - linkThis came up on the last article about these drives as well. Currently I'm running six 3TB Reds in a RAID-6. Over the last year they've rebuilt once a month. I have Linux set to log any errors, and it's never logged a single block error. With the double parity, it seems like it would have logged one by now if the actual URE were that high on a per-bit basis. This unit was a replacement for a unit using nine drives, which did have two drive failures in three years, but both failures were announced by SMART before any actual failure occurred. The SANs at work do scrubs once a week, and kick out about 2% of drives a year. It really seems like reality is better than the specifications in this case.
jaden24 - Friday, August 8, 2014 - linkWhy are they rebuilding once a month?
NonSequitor - Friday, August 8, 2014 - linkI have it set that way to spot a failing drive before it actually needs to be rebuilt. It's an orderly rebuild, checkarray, like this: http://www.thomas-krenn.com/en/wiki/Mdadm_checkarr...
In the past it has been useful as it has caused drives to throw a SMART error for reallocates during the process (with some 1TB drives) allowing me to replace them proactively.
jaden24 - Saturday, August 9, 2014 - linkInteresting. I had never heard of the practice before. Only consistent scrubbing, SMART configured, and extended burn-ins prior to use.
imaheadcase - Friday, August 8, 2014 - linkGanesh, could you get a response from Synology/asus/Qnap/etc as to why they don't have NAS with better CPU/RAM? Those products are nice, but many people wish to have them with more CPU/ram for media streaming. I find it very odd than none of the major players don't contribute to this market.
Why no 3ghz CPU and 16gig systems? It can't be cost since the ones that can be upgraded ram wise are cheap upgrades.
Out of the current popular NAS, only 2 support Transcoding, and multiple 1080p streams. But they have terrible software.
Gigaplex - Monday, August 11, 2014 - linkYou don't need a 3GHz CPU, 16GB RAM NAS to support media streaming.