Intel NUC13 Extreme Raptor Canyon Review: Sizzling SFF Performance Powerhouseby Ganesh T S on December 14, 2022 8:00 AM EST
- Posted in
- Raptor Lake
- Raptor Canyon
- NUC Extreme
The Intel NUCs started off in the early 2010s as ultra-compact form-factor boards / systems. The systems were meant to replace bulky tower desktops in applications where the physical footprint and system capabilities were significantly more than the actual requirements. The success of these UCFF systems has allowed Intel to slowly expand the product line to include a wide variety of form-factors.
Systems targeting the enthusiast and professional gaming (e-sports) markets require the integration of a discrete GPU in the system, and this has driven the development of NUC form-factors beyond the initial UCFF push. The Enthusiast NUCs integrate a discrete notebook-class GPU on the board, while the Extreme lineup allows end-users to install a discrete GPU of their own choice. The Raptor Canyon NUC13RNGi9 we are looking at today belongs to the latter family.
Earlier this year, Intel had launched the NUC12 Extreme Dragon Canyon with a 65W desktop Alder Lake CPU. Within a couple of quarters, they teased the NUC13 Extreme based on the recently-introduced Raptor Lake processors, with the promise of an imminent launch. The company kept its word with the announcement of a number of NUC13 Compute Elements and NUC13 Extreme Kit SKUs last month. Today's review takes a detailed look at the industrial design of the new NUC13 Extreme, provides some insights into the system configuration, and presents benchmark numbers encompassing a wide variety of use-cases.
Introduction and Product Impressions
Intel's NUC lineups targeting the gaming market fall under one of two categories - the Enthusiast family (Skull Canyon NUC6i7KYK, Hades Canyon NUC8i7HVK, Phantom Canyon NUC11PHKi7C, and Serpent Canyon NUC12SNKi72) and the Extreme family (Ghost Canyon NUC9QNX, Beast Canyon NUC11BTM, Dragon Canyon NUC12DCM, and Raptor Canyon NUC13RNG). The Raptor Canyon NUC is now donning the flagship NUC mantle, and brings the following updates over the Dragon Canyon NUC.
- Support for socketed processors with a PL1 of 150W (K-series). The thermal solution significantly increases the length of the Compute Element.
- Raptor Lake processor manufactured in Intel 7 with micro-architectural improvements for performance and power efficiency, continuing the usage of hybrid performance and efficiency cores.
- Support for DDR5-5600 SODIMMs, compared to DDR4-3200 in the previous generation Extreme NUCs.
- Increased chassis volume (13.7L vs. 8L) allowing integration of triple slot discrete GPUs.
- More traditional industrial design allowing easier access to I/O ports.
- External Wi-Fi antennae
Intel supplied us with an engineering sample of the flagship Raptor Canyon SKU - the NUC13RNGi9 sporting the NUC13 Extreme Compute Element (NUC13SBBi9). This Compute Element (Shrike Bay) is housed in a cuboidal 337mm x 317mm x 129mm chassis. We see a significant increase in volume (from 8L to 13.7L) compared to the Dragon Canyon NUC. This is still well within the realm of small form-factor (SFF) PCs - an adult can lug around the unit to LAN parties, if necessary. Other desirable SFF aspects such as the in-built PSU are carried over from the previous generation Extreme NUCs.
Intel's NUC lineup has traditionally included board and kit variants, allowing its partners to provide value additions (such as a passive chassis or additional I/O ports in the end system). Kits (other than the ones that come with a pre-installed OS) require the end-user to add storage, DRAM, and install an OS to complete the system. Intel plans to sell three varieties of the Raptor Canyon NUC Kit - the NUC13RNGi7 and the NUC13RNGi5 (equipped with the Core i7-13700K and Core i5-13600K respectively) in addition to the NUC13RNGi9 we are looking at today. However, OEMs and end-users can also build their own NUC13 system based on the following components:
- Compute Element (NUC13SBBi(9/5/7)(F))
- Baseboard (or backplane)
- DRAM (up to 2x DDR5-5600 SODIMMs)
- Non-volatile storage
- Discrete GPU (optional)
An off-the-shelf Raptor Canyon NUC13RNGi9 kit leaves only the DRAM, non-volatile storage, and discrete GPU to the choice of the end-user. Even though the Compute Element sports a LGA1700 socket, the three Compute Elements being sold in the market as part of the kit version come with the processor pre-installed (Core i9-13900K, or Core i7-13700K, or Core i5-13600K). Prior to the platform analysis and overview of our review configuration, let's take a look at the pre-decided components in the above list.
The Shrike Bay NUC13 Compute Element
The NUC13RNGi9 we are reviewing today comes with the NUC13SBBi9 NUC13 Extreme Compute Element. It comes with a socketed LGA1700 processor - the Core i9-13900K. This belongs to the Raptor Lake (13th Generation) family and has a 8P + 16e / 32T configuration. The processor base power is 125W, but the thermal design of the Compute Element as well as the chassis allows Intel to configure the processor with a PL1 of 150W and a PL2 of 250W (with a tau of 28s). It can turbo up to 5.8 GHz.
Similar to the previous Compute Elements, the Shrike Bay models also reimagine the traditional motherboard in a discrete PCIe add-on card form-factor. Unlike previous Compute Elements, Shrike Bay has more than 16 lanes connecting to the baseboard. The design of the Dragon Canyon's Compute Element is retained for the most part - a cooling shroud with a single fan and multiple M.2 heat-sinks with thermal pads pre-attached. However, the cooling solution for the CPU is redesigned to accommodate a heat-sink hanging off the edge of the Compute Element. The SODIMMs slot in vertically. The Z690 chipset used in the Dragon Canyon is re-used in Shrike Bay.
In terms of I/O, the Shrike Bay Compute Element puts every other mini-ITX motherboard for Raptor Lake to shame. It is equipped with dual Thunderbolt 4 ports, a 10G BASE-T AQC113C AQtion NIC, a 2.5G BASE-T Intel NIC, 6x USB 3.2 Gen 2 Type-A ports in the rear, and Realtek ALC1220 analog audio ports. The front panel is serviced by a daughterboard to provide a USB 3.2 Gen 2x2 (20 Gbps) Type-C port and two USB 3.2 Gen 1 Type-A ports.
Raptor Canyon Baseboard
The baseboard for the NUC13RNGi9 is a complete re-work over the Eden Cove used in the Dragon Canyon NUC. Intel has pushed out functionality such as SATA ports and USB headers into the baseboard in the new version. One of the key physical changes is the placement of the add-in card slots for the Compute Element and the discrete GPU on different sides of the baseboard. This allows the Compute Element to be mounted on top, and the discrete GPU of similar width to go under it.
The PCIe lanes are Gen 5, and do not have bifurcation support, similar to Eden Cove.
Chassis and PSU
The NUC13RNGi9 chassis has a much improved ease of installation compared to the previous generation NUCs. The dimensions allow the installation of triple-slot GPUs up to 317mm in length. The PSU also sees an upgrade, moving to a 750W modular one (compared to the 650W version seen in the Dragon Canon NUC), while retaining the 80+ GOLD rating.
Unlike the non-intuitive hinge-based design of the previous Extreme NUCs, opening up the Dragon Canyon NUC is straightforward - taking out a couple of screws and sliding out the top and perforated side panels prior to popping out the Compute Element. The thermal design works by pulling in air from the left, allowing it to go over the heat-sink hanging off the edge of the Compute Element and exit on the other side.
The SSD slots can be accessed on the rear of the Compute Element. As the chassis fans / shroud blocks access to the Compute Element's rear, it becomes mandatory to get the Compute Element out of the baseboard to install M.2 SSDs. There are two horizontal slots that are off the chipset, while the vertical one is the CPU-attached NVMe-only slot.
The SODIMMs can be installed without taking the Compute Element out of the baseboard. Baseboard features such as the dGPU slot and SATA ports / other headers can be found on the underside - the Compute Element itself doesn't need to be removed to get to them. GPU installation is much simplified without having to cram it into a tiny space shared with the Compute Element. The freedom also ends up giving plenty of airflow space for the discrete GPU.
The extra room also ensures that the cables connecting the high-speed I/Os on the daughterboard to the Compute Element are not easily dislodged. That was one of the main complaints I had with the previous Extreme NUCs - reinstalling or swapping GPUs would result in the front USB ports operating in USB 2.0 speeds. Fortunately, the Raptor Canyon NUC completely avoids those types of issues, thanks to the redesigned chassis. The I/O ports are also no longer recessed, allowing for easy access during day-to-day use.
The configuration of our review sample of the NUC13RNGi9 was completed with the following components:
- 2x 16GB Kingston Fury Impact KF548S38-16 DDR5-4800 SODIMM (38-38-38-70 @ 4800 MHz)
- 1x 1TB Kingston Fury Renegade SSFYRS1000G M.2 2280 PCIe 4.0 x4 NVMe SSD
- ASUS TUF-RTX3080TI-12G-GAMING NVIDIA GeForce RTX 3080 Ti
The ability to support a powerful GPU like the RTX 3080 Ti means that the Raptor Canyon NUC should easily be able to compete against massive gaming rigs. For now, we restrict ourselves to comparing it against the previous generations of Extreme NUCs. In the next section, we take a look at the full specifications of our review sample, followed by a detailed platform analysis along with some notes on our setup experience.
Post Your CommentPlease log in or sign up to comment.
View All Comments
meacupla - Wednesday, December 14, 2022 - linkI think this is one of the most disappointing NUC extremes released to date.
It's too large, and it's too boring looking. It's dimensions, and external looks makes it too similar to cheapo mATX business PCs from the likes of Dell, HP, and Lenovo.
Fractal Design's Ridge is a full 1L smaller, at 12.6L, it looks nice, and it can also fit a similarly large triple slot 335mm length GPU. And it's not like the Ridge does anything special, or use custom parts. It's just a bog standard mITX+SFX using a riser card.
Intel, please do better next time... Why even use a custom mobo, if you end up using a compact mATX case?
rob89353 - Wednesday, December 14, 2022 - linkOh no, 8% larger than the Ridge, what a disappointment. ??
The fact that it's the same size as a boring business PC but has a 13900 and 3080TI is what makes it impressive. It's like you packed a Corvette's V8 into a Chevy Spark.
lunchb0x91 - Wednesday, December 14, 2022 - linkExcept it's not even impressive. The Dan case C4-SFX is slightly smaller than this, supports standardized components, and can fit a 3090 in it.
PEJUman - Monday, January 2, 2023 - linkI do like the intel MOBO with dual TB4 with full bandwidth, 10 GBe, 2.5 GBe and 3x M.2 PCI-E 4x.
Additionally, the OTS option for CPU cooler that fits inside DAN case would struggle at the 150W sustained.
I'd like INTEL approach here on the motherboard form factor rethinking, but they need some industry support for the case & power supplies
meacupla - Wednesday, December 14, 2022 - linkYeah, it's massively disappointing, when you can pack a 13900 and 3080Ti into a smaller case.
Do you know how much 1L is in mini PC terms? You can get a mini PC equipped with a Ryzen 5700G or 6800H in that size.
Samus - Thursday, December 15, 2022 - linkThe FT03-Mini can pack a 13900 and 3080Ti into a case of nearly identical volume and it's a 10 year old design that uses a standard SFX PSU, has an optical drive slot, multiple 2.5" and 3.5" drive bays, and provisions for liquid cooling radiator mounting (which is basically required since there isn't room to fit a fist inside the case)
Unfortunately due to its design, a GPU with a blower is required and those are virtually non-existent anymore.
TheinsanegamerN - Wednesday, December 14, 2022 - linkBut there are smaller cases that can do the same thing without the proprietary slots and boards.
If you're gonna go proprietary not being able to beat the standard cases in size is a pretty big disappointment.
powerarmour - Wednesday, December 14, 2022 - linkSo, 'Next Unit of Computing' has now become 'Thin Tower Desktop', if you lay this thing on it's side you can put a CRT on top just like old times...
That's enough Intel, just stop with the NUC branding now, it's just dumb.
GoogleQuizz1 - Friday, December 30, 2022 - linkThe information given in your blog is very useful, thank you sir
Mike Lee - Wednesday, December 14, 2022 - linkThe one difference between this NUC and the Fractal Design Ridge (and the new Silverstone MILO 12) is the size of the CPU cooler. The largest CPU air cooler that you can fit in the Ridge is the Noctua NH-L12S, which is a single fan 120 mm cooler. It's obvious to me that the NUC engineering team was playing Tetris when they designed the cooling solution for this NUC. I think they were benchmarking the Noctua cooler to try and come up with something more performant and to also keep the size as small as possible.
What I hope to see is that intel further supports this design so that in the future we can reuse the power supply and case when we upgrade the compute elements to the latest generation of intel processors.