The Factory

OCZ's factory is located in Zhongli, which is a district of Taoyuan City, about a 45-minute drive away from the center of Taipei. Technically the factory is now owned and operated by Powertech Technology Inc (commonly known as PTI) because Toshiba wanted OCZ to sell the factory as a part of the acquisition. PTI is a relatively big name in the manufacturing industry with over 10,000 employees and a number of high value customers (including Apple, for instance). Aside from assembly, PTI also does wafer probing and die packaging and actually all Toshiba NAND is packaged by PTI (to my knowledge Samsung is the only NAND supplier that does all NAND packaging in-house), so the company has strong relationship with OCZ and Toshiba. While visiting the factory, I certainly got the feeling that OCZ and PTI are very well integrated as the cooperation between the two is effectively frictionless, which is partially explained by the fact that prior to the acquisition, the employees of the factory had paychecks directly from OCZ. 

Two surface-mount technology (SMT) lines in the factory are dedicated to OCZ with a total capacity of approximately 70,000 units per month. OCZ also has burst capacity with other SMT lines and factories that PTI owns in case there's a sudden spike in demand (e.g. a large enterprise order). The facility has room for up to ten SMT lines and OCZ is looking to increase production capacity in the future. However, the factory isn't fully exclusive to OCZ as PTI does manufacture other vendors' drives too and during the tour I spotted some Kingston SSDs.

Assembling an SSD

Assembling an SSD isn't really any different from any other component that is built on a printed circuit board (PCB). The process itself is very straightforward and contains only a handful of steps which should be the same for every manufacturer.

The process begins by printing the circuit board and coating the chip/resistor sockets with solder paste, which is done in the machine pictured above. 

The solder paste must be stored in near-zero temperature at all times or otherwise it will lose its soldering characteristics. It can only withstand room temperature for a couple of hours before becoming waste, which is why the paste is stored in small cans to minimize the loss.

Once the PCB has been printed and solder paste applied, the end result is what's pictured above. Four 2.5" PCBs can be processed at the same time, but obviously a smaller PCB would result in higher throughput since more PCBs would fit in the same area and could be processed simultaneously for better cost efficiency. That's why we've seen some manufacturers adopting smaller PCBs in 2.5" drives.

The PCB is now ready to take on the actual chips, which are mounted on the PCB by the above mounter. Every individual chip, resistor and capacitor is loaded to the machine in a circular "tape and reel" and the machine then automatically mounts the components to their right places on the PCB.

The controller come in a slightly different tray and it's the last component to be mounted before the drive moves to the cooking stage.

With all the components in place, the drives enters the reflow oven that melts the solder paste and secures electrical connectivity between all chips. The whole reflow process takes about five minutes and the temperature increases gradually at first before dropping quickly in the last stage of the reflow. The exact temperature profile is unique and has been achieved through science, but there's also trial and error in the mix. 

After the reflow the PCBs go through an automatic optical inspection, which compares the produced PCBs against a picture of a perfect PCB to spot any errors (such as misaligned chips and insufficient solders). The automatic inspection is followed by a manual human eye inspection to ensure that all PCBs passing this point should be, at least visually, suitable to go on sale. 

For double-sided PCBs, the whole procedure from printing the PCB to visual inspection is then repeated because only one side of the PCB can be worked at a time. That's why many smaller capacity SSDs we see are single-sided because it essentially cuts the PCB assembly steps in half, which reduces cost. 

The final step of the PCB assembly is to connect the SATA and power connector, which is separate from the rest of the PCB. I've seen a couple of SSDs where the SATA and power connectors are actually integrated to the PCB, which saves one assembly step, and it's also something that OCZ is considering, but for now the connector remains separate. In M.2 the connector is always a part of the PCB, so from a manufacturing perspective M.2 is slightly more cost efficient than 2.5" drives are.

Once the PCB assembly is fully complete, the PCBs are separated and cut from the frame. The PCB is then put inside the final metal chassis and the screws are screwed automatically by the machine above. 

Introduction & The Development Process of an SSD Firmware Installation & Run-In Testing
Comments Locked


View All Comments

  • Murloc - Wednesday, May 20, 2015 - link

    cosmically in tact?

    Lol I guess it's the jet lag or the phone dictionary.
  • harrynsally - Wednesday, May 20, 2015 - link

    From reading actual user reviews (e.g. # of 5/4 stars vs. 1/2 starts at places like Newegg), I have not gone wrong after buying a number of Samsung 850 EVO and Micron/Crucial MX100 250GB class SSDs.

    Of course it's not just counting stars, but understanding the user experience/satisfaction.

    Although SSD street prices have really come down recently (e.g.currently 250 GB class 850 EVO = $89, ARC 100 $69 after $20 OCZ rebate etc.), will move up to 500 GB SSDs. After reading reviews in this size, my money still goes to Samsung and/or Crucial.
  • ocz_tuff_bunny - Wednesday, May 20, 2015 - link

    Hi harrynsally,
    Thank you for your comment. We totally agree when choosing a SSD it's not just counting stars, but understanding the user experience/satisfaction. OCZ is a new organization under Toshiba and have made significant changes to everything from processes to production. We hope one day we will have the opportunity to show you our commitment to user experience/satisfaction through our products.
  • RU482 - Wednesday, May 20, 2015 - link

    ummm, where did my post go?
  • Shadow7037932 - Wednesday, May 20, 2015 - link

    Wow, I'm surprised they are using normal PCs for loading up the firmware. I would have expected some custom setup for this. I guess at these volumes it makes sense to to it this way.
  • RyanVM - Thursday, May 21, 2015 - link

    Hate to say it, but OCZ as a brand is too toxic for me to touch anymore.
  • edlee - Thursday, May 21, 2015 - link

    I am not sure why they are still using ocz brand, I would much rather hear them call it Toshiba performance line, ocz will always have a negative connotation in my subconscious.

    I understand its run by Toshiba, and completely different management style but still, I feel safer with a big brand name behind my ssd, like crucial and Samsung. I would accept Toshiba as a quality band supplier , just dump the ocz brand
  • Murloc - Thursday, May 21, 2015 - link

    I don't feel safe with samsung after the 840 evo fiasco
  • Oxford Guy - Friday, May 22, 2015 - link

    The EVO sucks but it's not even close to the OCZ fiasco with the Vertex 2. That involved pure bait and switch fraud and worse. Then they followed it up with the 3 line which was also buggy.
  • Oxford Guy - Friday, May 22, 2015 - link

    "I am not sure why they are still using ocz brand"

    For the same reason Nvidia's website lists the 970 as having 4 GB of 224 GB/s VRAM. They know consumers are stupid, generally — with attention spans rivaling the common gnat.

Log in

Don't have an account? Sign up now