The Factory

OCZ's factory is located in Zhongli, which is a district of Taoyuan City, about a 45-minute drive away from the center of Taipei. Technically the factory is now owned and operated by Powertech Technology Inc (commonly known as PTI) because Toshiba wanted OCZ to sell the factory as a part of the acquisition. PTI is a relatively big name in the manufacturing industry with over 10,000 employees and a number of high value customers (including Apple, for instance). Aside from assembly, PTI also does wafer probing and die packaging and actually all Toshiba NAND is packaged by PTI (to my knowledge Samsung is the only NAND supplier that does all NAND packaging in-house), so the company has strong relationship with OCZ and Toshiba. While visiting the factory, I certainly got the feeling that OCZ and PTI are very well integrated as the cooperation between the two is effectively frictionless, which is partially explained by the fact that prior to the acquisition, the employees of the factory had paychecks directly from OCZ. 

Two surface-mount technology (SMT) lines in the factory are dedicated to OCZ with a total capacity of approximately 70,000 units per month. OCZ also has burst capacity with other SMT lines and factories that PTI owns in case there's a sudden spike in demand (e.g. a large enterprise order). The facility has room for up to ten SMT lines and OCZ is looking to increase production capacity in the future. However, the factory isn't fully exclusive to OCZ as PTI does manufacture other vendors' drives too and during the tour I spotted some Kingston SSDs.

Assembling an SSD

Assembling an SSD isn't really any different from any other component that is built on a printed circuit board (PCB). The process itself is very straightforward and contains only a handful of steps which should be the same for every manufacturer.

The process begins by printing the circuit board and coating the chip/resistor sockets with solder paste, which is done in the machine pictured above. 

The solder paste must be stored in near-zero temperature at all times or otherwise it will lose its soldering characteristics. It can only withstand room temperature for a couple of hours before becoming waste, which is why the paste is stored in small cans to minimize the loss.

Once the PCB has been printed and solder paste applied, the end result is what's pictured above. Four 2.5" PCBs can be processed at the same time, but obviously a smaller PCB would result in higher throughput since more PCBs would fit in the same area and could be processed simultaneously for better cost efficiency. That's why we've seen some manufacturers adopting smaller PCBs in 2.5" drives.

The PCB is now ready to take on the actual chips, which are mounted on the PCB by the above mounter. Every individual chip, resistor and capacitor is loaded to the machine in a circular "tape and reel" and the machine then automatically mounts the components to their right places on the PCB.

The controller come in a slightly different tray and it's the last component to be mounted before the drive moves to the cooking stage.

With all the components in place, the drives enters the reflow oven that melts the solder paste and secures electrical connectivity between all chips. The whole reflow process takes about five minutes and the temperature increases gradually at first before dropping quickly in the last stage of the reflow. The exact temperature profile is unique and has been achieved through science, but there's also trial and error in the mix. 

After the reflow the PCBs go through an automatic optical inspection, which compares the produced PCBs against a picture of a perfect PCB to spot any errors (such as misaligned chips and insufficient solders). The automatic inspection is followed by a manual human eye inspection to ensure that all PCBs passing this point should be, at least visually, suitable to go on sale. 

For double-sided PCBs, the whole procedure from printing the PCB to visual inspection is then repeated because only one side of the PCB can be worked at a time. That's why many smaller capacity SSDs we see are single-sided because it essentially cuts the PCB assembly steps in half, which reduces cost. 

The final step of the PCB assembly is to connect the SATA and power connector, which is separate from the rest of the PCB. I've seen a couple of SSDs where the SATA and power connectors are actually integrated to the PCB, which saves one assembly step, and it's also something that OCZ is considering, but for now the connector remains separate. In M.2 the connector is always a part of the PCB, so from a manufacturing perspective M.2 is slightly more cost efficient than 2.5" drives are.

Once the PCB assembly is fully complete, the PCBs are separated and cut from the frame. The PCB is then put inside the final metal chassis and the screws are screwed automatically by the machine above. 

Introduction & The Development Process of an SSD Firmware Installation & Run-In Testing
Comments Locked


View All Comments

  • fatpugsley - Wednesday, May 20, 2015 - link

    A root GUI with presumably obsolete stock Fedora doesnt seem very secure to me.
  • Stahn Aileron - Thursday, May 21, 2015 - link

    Doesn't really matter if the only network they're connected to is an internal network without internet access. The only thing those workstations should be touching and working on are SSDs. There's minimal security needs there. The best and simplest security measure there would just be an air gap.
  • dreamslacker - Thursday, May 21, 2015 - link

    It's not as uncommon as you might think. Most of the machines are effectively on an 'intranet' so they really only need a UI and kernel base that has reasonably good OoB driver support for commodity hardware and the dependencies for the specific in-house software suite.

    When I worked a short project on similar lines in Seagate back in the past, their machines ran Centos 4.4 (at the time) and they started off that line-up on RHEL before moving to Fedora Core and then to Centos 4.4. They were planning a move back to Fedora after that though.
  • der - Wednesday, May 20, 2015 - link

    They're made to they can dig deep to our pocket monies.
  • Scott_T - Wednesday, May 20, 2015 - link

    Next time make us a movie in the format of 'How its Made'
  • MrSpadge - Wednesday, May 20, 2015 - link

    I'd rather read an article at my own pace.
  • jann5s - Wednesday, May 20, 2015 - link

    Cool stuff Kristian!
  • YoloPascual - Wednesday, May 20, 2015 - link

    Wow a field trip.
  • OzzieGT - Wednesday, May 20, 2015 - link

    That poor soul who has to apply labels all day...
  • junky77 - Wednesday, May 20, 2015 - link

    this fake smile.. seems like all the people interviewed on AT and such have this smile lol

Log in

Don't have an account? Sign up now