In and Around the Fractal Design Define XL R2

If you're familiar with Fractal Design's aesthetic for the Define series, the Define XL R2 isn't going to bring any surprises. Fractal Design continues to offer their cases in black and gunmetal finishes, and I continue to be pleased with the gunmetal; it's a gray that doesn't clash with computer hardware, but keeps the box from looking too bland. We're really in an age where we've replaced the beige box with the black box.

The front of the XL R2 features a padded door which opens to the left and conceals four 5.25" drive bays with ventilated snap-in/snap-out shields. The entire front fascia is ventilated on the sides just like the other Define cases, allowing plenty of cool air to enter the case without letting noise escape. Next to the drive bays is a three-step switch for the fan controller; you can run fans connected to the controller at 5V, 7V, and 12V. Below the bays are two intake fan mounts; Fractal Design includes a 140mm fan in one, but you have to add your own fan to the second. These fans are hidden behind a fan filter and are easily removed and replaced.

When we move to the top of the XL R2, we find the power button and reset button along with the I/O all placed on the front edge of the case. The remainder of the external shell of the XL R2 is flat, matte black, though there are 120mm/140mm fan mounts on the top and side of the case (two on the top, one on the side panel). In true Fractal Design fashion, these mounts are blocked off with removable acoustic padding.

Someone at Fractal Design must have been paying attention to my recent complaining (I'd like to think they were though it probably isn't true), because the side panels are hinged instead of notched. Per usual, two thumbscrews hold them into place, but they're very easy to put on and take off.

The interior of the Define XL R2 is nothing new; this is very much just a larger Define R4. The two drive cages are both modular, and can be removed or rotated to suit your airflow needs. Alternatively, you can mount a single cage where the bottom intake fan is and install a radiator in the front of the enclosure. Fractal Design continues to employ their tried and true white steel drive sleds, and I'm not complaining. I've seen enough vendors nail every other part of the design and then screw these up fantastically that I appreciate when someone has them down about as good as they'll get.

The remainder of the XL R2's interior isn't bad by any stretch of the imagination, but it's still a hair behind the times. We do get a 140mm intake fan on the bottom of the case and the case itself stands up high enough that only the shaggiest of carpet will block it off, and Fractal Design actually includes additional clearance above the motherboard tray expressly for mounting 240mm/280mm slim radiators. Where they fall behind is the lack of an extruded channel around the tray for cable management (as well as helping the case slim down a touch) and no preinstalled motherboard standoffs or alignment studs.

It's tough to complain too much, though. This is effectively the same ATX interior cooling design Nanoxia and everyone else enjoys, it's just bigger. I do think it's unusual that Fractal Design opted to go for a bottom intake instead of using that third fan in the open front mount, but "unusual" doesn't necessarily mean "bad." As I mentioned, the XL R2 does actually stand far enough off of the ground to make this intake a useful one. A bottom intake's noise can be easily muffled by its direction and proximity to the ground.

Introducing the Fractal Design Define XL R2 Assembling the Fractal Design Define XL R2
Comments Locked

46 Comments

View All Comments

  • omgia - Wednesday, February 20, 2013 - link

    I moved from a p180 to an Define R4 recently. The most notable difference between this and the p180 is the cable routing. There is a significant difference in the amount of space behind the motherboard for routing cables. Also, my R4 is 4-6 degrees cooler (F) than my Antec P180 was with the supposedly better thermal sections. This may be because these cases uses 140 vs 120mm fans. But also, with the ability to get all of the wires behind the motherboard, you have better airflow. Something I was personally never able to achieve with the P180. I like the build quality of this case better than the P180 as well. Support for front USB 3.0 is also nice. I was thinking about getting a P280, but after completing my build, I have no reservations that the R4 or XL-R2 are better cases.
  • akhaddd - Wednesday, February 20, 2013 - link

    eep Silence cases are already pretty heavy and well built in their own right, then add another ten pounds and three inches. The Define XL R2 is made almost entirely of steel with really the bare minimum of plastic used in its
  • lwatcdr - Wednesday, February 20, 2013 - link

    With the new closed loop systems from Corsair, NZXT, and Swift tech it would be nice to know which fit in the case. Yes I know you can not test with every Motherboard but they are becoming mainstream so it would be helpful to add that data even if it just "The mounting screws will fit.
  • omgia - Wednesday, February 20, 2013 - link

    I just purchased a Define R4 and one of the biggest problems is reaching the 12V lead up to the top-left of the case.I'm sure most would fit if routed over the top of the motherboard, but you really need a long one to route through the grommets.

    One feature of the XL-R2 and the R4's are mounting spaces for SSDs on the back of the motherboard tray. This seems like a great idea at first, but you must mount it prior to installing the motherboard (meaning you'll have to remove the motherboard to remove the drive). And the mounting positions are far enough away from the other drives, it may be difficult to share a power lead between the drive trays and the 2.5" mount points. I was able to share one with a SATA lead with 3 connectors, but not a lead with 2. The center connector on the lead with 3 became useless.

    Not sure about the XL-R2, but on the Define R4, the center drive tray is subject to vibration from mechanical drives. Even with the screws on the drive tray holder secured tightly, there were significant vibrations that could easily be heard outside the case. This was evident even using the bottom screw holes with rubber grommets. I had to torque down these screws hard to get the vibrations to stop.

    As far as noise goes, these are silent cases, not silencing cases. The foam may help a little, but it is not going to really do any sound deadening. The case on its own is whisper quiet without any components. But I can still hear hard drives chirping and my noisier cpu fan. If you are replacing an existing case, listen to your system without all of your existing case fans running. That is how it will probably sound with an XL-R2 or Define R4. Maybe a decible or two lower, but nothing significant.
  • Touche - Wednesday, February 20, 2013 - link

    Is that GPU crooked?
  • snakyjake - Wednesday, February 20, 2013 - link

    I wanted a large case for a NAS/Multipurpose machine that will be in my home, so need something quiet.
  • bsix - Wednesday, February 20, 2013 - link

    With the Define (regular size) cases the inlet airflow is stifled because of the drive cages and the more restrictive cages they use. This problem seems so be solved by using the bottom fan. This is really the only difference in these two cases from an airflow perspective.

    i bet the R4 would do much better with an additional inlet fan on the bottom and potentially some better case fans that can lower the noise floor an additional 2 db.

    This would be really appreciated - I bet the R4 would be equal to both the nanoxia and the XL R2 in acoustics with this setup.

    Take care.
  • stratosrally - Wednesday, February 20, 2013 - link

    I do realize that Anandtech is known for pulling no punches (and am thankful for that!) but the article really doesn't come across positively enough. The fact that it is such a large case, comes with 3 fans & a fan controller, and performs so well for a suggested list price of only $129.99 ought to be given more emphasis in this review.

    The review seems to be almost begrudging in admitting that the XL R2 does so well across the board. For example, the amount of room for cable routing (26mm - more than an inch!) precludes the need for channels in the motherboard plate which would just add complexity and cost.

    BTW - the constant promotion of the Nanoxia can be a bit frustrating given that it still isn't available in the US. It, too has no motherboard guide post and you mentioned similar issues in installing the PSU. You also mentioned I/O panel & GPU installation issues. You actually stated you might be coming across as nitpicking in that review, yet gave it the Bronze Editor's Choice Award.

    I personally think there's a limit to how much reasonably-priced enclosures can ease assembly. I don't mind installing my own standoffs and paying attention (using both hands, etc.) when installing the PSU. Given the variety of motherboard sizes this case will accept you'd quite possibly be adding or subtracting standoffs anyway.

    If I wanted everything done for myself I'd expect to pay a more premium price. As this case is larger and performs equal to or better than the Deep Silence 1 in the tests - IMHO it deserves the Silver or even Gold Award.
  • five_seven - Thursday, February 21, 2013 - link

    After reading so many reviews I, too, am tired of hearing about stand-offs not being installed on a motherboard. An enthusiast building their own PC is doing just that-- building their own PC. If people really feel dragged out by having to figure out how to align a motherboard with a lack of stand-offs or a center stud, they've got bigger problems.

    Rather than docking any points from your " utterly worthless, arbitrary point system" over this issue, might I suggest simply indicating if a case provides stand-offs and if the user will need to install them or not. Some objectivity in regards to this issue, however, would be nice.
  • UNhooked - Thursday, February 21, 2013 - link

    Once again no watercooling support of any kind was discussed. You really need to start incorporating this. It is now a vital part of case reviews based on mainstream watercooling has become.

Log in

Don't have an account? Sign up now