The OnLogic Helix HX500 Review: A Rugged Fanless 35W mini-PCby Ganesh T S on September 17, 2021 10:00 AM EST
- Posted in
- Industrial PC
- Passive Cooling
- Comet Lake
The emergence of edge computing as a paradigm has expanded the market for industrial PCs over the last few years. Traditionally an 'industrial PC' was built with a focus on reliable operation in a rugged environment - the emphasis on computing performance being secondary to the utility. This has changed recently with the need to process more data at the edge.
OnLogic (formerly, Logic Supply) has been servicing the embedded / industrial PC market with pre-configured small form-factor (SFF) systems since 2003. We have reviewed multiple systems from OnLogic before, such as the Broadwell-based ML100G-30 and the Skylake vPro-based ML100G-50. Both fanless systems were based on Intel's U-series processors configured with a 15 - 20W TDP.
In mid-2020, OnLogic introduced the Helix line of industrial PCs. The 300-series (based on Intel Elkhart Lake) caters to the IoT edge computing market with the traditional CPU performance requirements. The Helix 500 and 600-series are based on Intel Comet Lake, and services the market opened up by the increased demand for performance density in edge computing. This review takes a look at the performance and value proposition of a high-end Helix HX500 configuration based on the Intel Core i7-10700T.
Onlogic Helix HX500: Core i7-10700T at 35 W
Passively cooled computing systems are one of the top choices for industrial PCs, where reliability and ruggedness are key requirements. The absence of noise, ventilation slots, fans and associated maintenance requirements, etc. serve as important advantages in many deployments where servicing is difficult and a long life cycle is required. OnLogic's Helix lineup of rugged industrial PCs was introduced in mid-2020 to cater to this market.
OnLogic's Helix line uses a board based on Intel's Q470 chipset. The HX500 is the most compact of the lot, coming in at 154mm x 210mm x 50.8mm. The HX600 approximately doubles the width of the system to add space for a GPU slot (using a GPU makes the system an actively cooled hybrid - the motherboard is still passively cooled). The HX610 retains the HX600 form-factor, but uses the additional space for dual SATA drive bays.
The OnLogic Comet Lake Helix Series - HX500, HX600, and HX610 (from L to R)
OnLogic sent over a fully pre-configured sample of the Helix HX500 earlier this year to put through our rigorous evaluation routine for fanless SFF PCs. The specifications of the review sample are summarized in the table below.
|OnLogic Helix HX500 Specifications
|Processor||Intel Core i7-10700T
Comet Lake 8C/16T, 2.0 - 4.5 GHz
Intel 14nm, 16 MB L2, 35 W
|Memory||KInnoDisk M4S0-AGS1O5IK DDR4-2666 SODIMM
19-19-19-43 @ 2666 MHz
|Graphics||Intel UHD Graphics 630|
|Disk Drive(s)||Transcend TS256GMTS800
(256 GB; M.2 Type 2280 SATA III; MLC NAND)
|Networking||1 × GbE port (Intel I219-V)
1 × GbE port (Intel I210-AT)
|Audio||3.5mm Headphone Jack (Realtek ALC233)
Capable of 5.1/7.1 digital output with HD audio bitstreaming (DP)
|Miscellaneous I/O Ports||4x USB 3.2 Gen 2 Type-A (front)
2x USB 3.2 Gen 2 Type-A (rear)
2x USB 3.2 Gen 1 Type-A (rear)
|Operating System||No OS as shipped / default option,
We installed Windows 10 Enterprise x64 21H1
|Pricing||$887 (base configuration)
$1694 (as configured / No OS)
|Full Specifications||OnLogic Helix HX500 Specifications|
It must be noted that the $887 price for the base configuration is not a barebones one - it includes the Intel Celeron G5900T dual-core 35W processor, a 4GB DDR4-2666 SODIMM, and a 64GB M.2 SATA SSD. Since our review configuration was shipped with the OS configured as 'None', we had to download the drivers off OnLogic's support site to ensure that the system was up and running optimally after the Windows installation. A 120W (20V @ 6A) power adapter is bundled along with the package. The system can be wall-mounted (accessories sold separately), or used directly on a desktop (adhesive rubber bumpers bundled).
The various chassis features are brought out in the gallery below.
Disassembling the system to upgrade the storage and RAM is quite straightforward and doesn't involve messing around with the thermal solution. Four screws holding the rear I/O panel in place, and two screws that fasten the bottom panel need to be removed.
Installing M.2 drives and SODIMMs are as simple as just slotting them in. The thermal solution for the SSD can also be seen in the above picture.
The Helix HX500 chassis is solidly built, and appears to possess a thermal solution capable of handling 35W processors. At the same time, the ease of upgrading the DRAM and storage has not been sacrificed. The system I/Os match the expectations from an industrial PC. The ridges on the chassis are a tad sharper than other fanless PC chassis we have seen before - so, a little care is warranted while handling the unit even if one is used to handling PC cases that also double up as heat sinks.
In the next section, we take a look at the BIOS options along with an analysis of the motherboard platform. Following that, we have a number of sections focusing on various performance aspects. Prior to the conclusions, we also take a look at the thermal profile of the system under stress. Read on for the full review.
Post Your CommentPlease log in or sign up to comment.
View All Comments
lightningz71 - Friday, September 17, 2021 - linkWhile this is a neat package, I'm personally more interested in the H600. It has an x16 PCIe slot for adding a card in. While some might add a graphics card, I'd much rather add a 4 port Ethernet card as this is a good size for a homebrew router/firewall. Unfortunately, it gets rather expensive, and there are other solutions out there that are more cost efficient.
YB1064 - Friday, September 17, 2021 - linkI agree. Option for an add in PCIe card would be better. Also, more ethernet ports are very useful in an industrial environment as several systems such as machine vision cameras , laser trackers etc have Ethernet IO.
ZPrime - Friday, September 17, 2021 - linkProblem is that stupid DMI link, which AFAIK is PCIe 3.0 x4 (so not quite 4GB/sec).
4x 1GbE should be OK, as long as you aren't also doing anything intensive via USB3, or doing too much with the M.2 storage...
saratoga4 - Friday, September 17, 2021 - link>4x 1GbE should be OK
~4x100 MB/s will definitely be ok on a 4000 MB/s PCIe link. 4x 10Gbe would be a little tighter, but ok in most realistic scenarios.
Frenetic Pony - Friday, September 17, 2021 - linkLot of problems with it. High price for what you get, out of date specs, no way to update any of it as you have to buy configged. The case is the real draw here, even just selling an up to date barebones setup at a relatively high price would be preferable to what you can get from OnLogic.
Like, I get why. They're a specialty shop. But I suspect opening up past their industrial focus, where form factor and fanless and such is more important than specs and budget might get them a new customer segment. I'd certainly be a potential customer if they did, but I'm not holding out hope.
email@example.com - Sunday, September 19, 2021 - linkhere list of whatspp group link
Threska - Friday, September 17, 2021 - linkThe two should be sufficient since a lot use a switch anyway, which would be smaller than this box.
sarahmarcus - Tuesday, March 8, 2022 - linkHere is the collection of whatsapp group invite links.
TheinsanegamerN - Friday, September 17, 2021 - linkThat H600 box is really neat, but over $1000 for that is an eye watering price (granted I know its specialty equipment, but still).
zmeul - Friday, September 17, 2021 - link"are suitable for industrial applications requiring longevity and minimal maintenance"
since I had to deal with older units like the HX500, I would say they are not suited for some industrial applications - the crux of the problem is that these units are not sealed at all and certain environments can utterly destroy them